#Splashtop streamer personal update
#Splashtop streamer personal pro
#Splashtop streamer personal software
#Splashtop streamer personal code

Steps to trigger Wake-on-Lan from remote network: You could also use the checking tool to make sure the settings are correct.There might be times when you will need to tap the Wake up this computer button several times instead of only one time, to ensure that the computer has been awakened.Then you can click on the 'Wake up' button under the PC name (button only appears when the PC is offline).Click on the 'gear' icon next to the PC you want to wake up.Tap on the Wake up this computer button to attempt to wake up the PC computer from either a Powered-off, Sleep or Hibernation state or a Mac computer from a Sleep state. A Wake up this computer button will display, as shown above.ĥ. On your tablet/phone, you should see the computer you want to awaken shown as an unavailable one (gray computer icon).Ĥ. Keep your computer ON, and make a successful connection, then shut down your computer (power off).ģ. On your tablet/phone, launch Splashtop Personal app.Ģ. Steps required to wake your computer from Sleep or Hibernation mode:ġ. Steps to trigger Wake-on-Lan from local network: If you are using only battery power on the laptop, this may cause an attempt to use the WoL feature to fail.

#Splashtop streamer personal pro

If your computer is a laptop (for example, a NB, Mac Book Pro or Mac Book Air), please make sure the power cable is plugged in to an electrical power source. Your computer must be connected to your wireless router using the network cable (Ethernet).Ĥ. Make sure the Wake for network access option is selected in the Energy Saver settings.ģ.Configure your LAN network interface adapter ( Control Panel -> Device Manager -> Network adapters).Enable Wake-on-LAN in the system BIOS if you want to allow your computer to wake from a powered-off (i.e., Hibernate) state.For example, it might be 'Wake on LAN,' or 'Onboard LAN Boot ROM,' or something else. Please note that the term in BIOS might vary. Configure your computer to be Wake-on-LAN ready. (This step pertains to PC only Mac users can ignore this.)Ģ. Make sure your BIOS supports Wake-on-LAN, and that this option has been enabled. To connect to your computer when it is in Sleep or Hibernation mode, you need the following:ġ. (New) On Windows 8 or 10, you need to disable 'Turn on fast startup' function to be able to wake it up from powered off state. Please note that currently, it is not possible to awaken a Mac computer from a powered-off state via the WoL feature, although it can be done from a sleeping state as described below.

Computer is connected by Ethernet, not WiFi.

Settings in Windows or Mac have been properly set up.

PC BIOS supports WoL and that the option has been enabled.

Otherwise, there is no chance to make WoL work successfully. In this topic, we provide the instructions.įirst, we ask that you make sure the following three conditions have been satisfied completely.

However, this is not an intuitive feature, and is performed using somewhat complicated settings. If you are a user of the Splashtop Enterprise v2 system, please refer to the link below for more information.Splashtop Personal provide a method to perform Wake-on-LAN (WoL) which is similar to Splashtop v1.x. The end users will only see the active installers in the deployment page.

#Splashtop streamer personal software

In the same Software page, Team Owner can activate and de-activate any of the installers. Please go to Splashtop Streamer Downloads to get 'pkg' installer. Log in to Splashtop Gateway web portal as Team owner, and go to System > Software, click Upload to upload the new version into the system.īrowse the installer, check the 'Set this pkg as active' option and start uploading. The Team Owner is responsible for uploading and maintaining the versions of Streamer in Splashtop Gateway.

#Splashtop streamer personal update

For Team Owner to update the Streamer download in the Gatewayįrom time to time, Splashtop releases new versions of Streamer to enhance the performance, stability and security with clear statement about version compatibility.

#Splashtop streamer personal code

Launching the Streamer for the first time, you are required to enter the Gateway IP address (including the port number) and the 12-digit deployment code and click Allow Access to complete the Streamer deployment.